SPLat Controls - USB-serial adaptors, RS485 adaptors programmable controller accessories

We offer a number of accessory products to go with your SPLat controller.

Some of these are 3rd party products we offer as a convenience service, and are not supported.

PC232

This is the CC18/MS120/HD8 programming cable. Note that the Developers' Kits include the cable.

1 - 4AUD36USD≈36
5 - 9AUD35USD≈35
10 - 24AUD33USD≈33

Shipping weight:
48g / 1.7oz

Units supplied may be of different appearance but will always be based on the FTDI chip

USB232

Not all USB to serial (RS232) adaptors are created equal. If your computer lacks a serial (COM, RS232 port) you will need an adaptor. The adaptor we offer is based on the FTDI chips, which have proven themselves the most dependable. We carry this adaptor purely as a convenience service, so you can order it with your SPLat Developer's Kit. Drivers can be downloaded from the FTDI download page. The VCP driver is the correct one.

1 - 4AUD54USD≈54
5 - 9AUD54USD≈54
10 - 24AUD53USD≈53

Shipping weight:
100g / 3.5oz

BT-TTL5

BlueTooth adaptor for CC18, MS120 and other SPLat controllers that have a 4-pin programming connector at 5V. Pre-configured as a slave device at 38400 Baud. Intended for use with SimpleHMI on Android.

1 - 4AUD36USD≈36
5 - 9AUD36USD≈36
10 - 24AUD36USD≈36

Shipping weight:
6g / 0.2oz

Units supplied may be of different appearance.

PSUS24630 US sales only

A US style switchmode wall plug style 24VDC 0.6A power supply. This is intended primarily for use during development work. It is supplied with the output wires unterminated so you can fit the appropriate SPLat power connector from your SPLat Developer's Kit. We carry this purely as a convenience service, so you can order it with your SPLat Developer's Kit.

1 - 4AUD32USD≈32
5 - 9AUD32USD≈32
10 - 24AUD31USD≈31

Shipping weight:
250g / 8.8oz

DB9MF-6

A 6' long DB9 M-F data cable. Use as a SPLat programming cable on your computer's 9-pin COM port or in conjunction with a USB232 adaptor.

1 - 4AUD14USD≈14
5 - 9AUD14USD≈14
10 - 24AUD14USD≈14

Shipping weight:
150g / 5.3oz

XP485

This adaptor connects to the Xwire port on any SPLat controller and converts it to an RS485 interface. Xwire protocol over RS485 will allow cable runs of up to 1km (with suitable cable and grounding precautions) and up to 32 devices.

Note: There is also an Xwire adaptor made specifically for the CC16/18, shown on that products's page.

1 - 4AUD35USD≈35
5 - 9AUD34USD≈34
10 - 24AUD32USD≈32

Shipping weight:
75g / 2.6oz

MB485

This adaptor plugs directly into the DB9 communications port on a SPLat controller and converts it to an RS485 interface. Typically you would use this to extend the range of ModBus communications up to 1km (with suitable cable and grounding precautions). Compatible with MMi202 and SL100.

1 - 4AUD42USD≈42
5 - 9AUD40USD≈40
10 - 24AUD39USD≈39

Shipping weight:
75g / 2.6oz

PC485

This adaptor plugs directly into the COM port on a PC and converts it to an RS485 interface. It features automatic Tx/Rx switching. Documentation

1 - 4AUD71USD≈71
5 - 9AUD68USD≈69
10 - 24AUD66USD≈66

Shipping weight:
150g / 5.3oz

ULNX6

Pack of 6 spare ULN2803A output chips

1 - 4AUD22USD≈22
5 - 9AUD21USD≈21
10 - 24AUD20USD≈20

Shipping weight:
25g / 0.9oz

SPLat Accessories